Zimmermann mold - Your global partner for tooling, service and repair As an international company, the company Zimmermann Formenbau GmbH, with over 125 years of experience and its extensive know-how of the leading manufacturers of injection molds for the automotive industry and other industries. We offer our customers a comprehensive service, from the design phase to after-sales service. With 140 experienced employees at its Gladenbach and farther locations in Portugal, Russia, China, USA and India, and partnerships around the world, we are to meet in a position our customers' demands in terms of quality, reliability and value for money. As a privately owned company, we offer our customers maximum flexibility and innovativeness. The cooperation of our technical know-how, coupled with high quality standards, is the key to our success.

In Reggio Emilia in 1935 founded in the form of a hand advertising drive. The company G. Guerra Group spa has gained considerable importance, and not only on the national territory. She is a Synoym of expertise, service and quality. It consists of 4 different autonomous separate Podukteinheiten: Press Production, production of sleeves, profiles and hoses; preparation of mixtures and production machining. The company has about 80 employees and this at a total area of approximately7,000 m2. The technical industrial progress is nowadays a considerable amount of raw materials available, ie natural rubber, synthetic rubbers and other specific additives by the company G. Guerra Group spa are selected between the manufacturers and distributors with an international reputation. For these commodities, G. produces Guerra Group spa with its own formula over 400 mixtures of a variety of types to meet the needs of customers in terms of the mechanical properties of tensile strength, tear resistance, friction resistance, compressive strength, elasticity, bending stiffness, aging resistance, liquid, heat, fire and satisfy cold resistance, as well as the conditions of the electrical insulation to kšnnen. The competence of the company G. Guerra Group spa begins with † HECK of the project of the sought-after part to realization with the Affordable equipment. It makes use of various manufacturing processes

Design of Injection works of the highest quality at selected Chinese partners.

LACK mold was founded in 1989 as a sole proprietorship in Melk (Lower Austria). Due to the good development and increasing demand, the company moved in 2000 to the newly built facility in Rye Village, a neighboring town of Melk. At that time, as the introduction of the single company in the mold LACK GmbH. Since the company's founding in 1989, the core competence in the design and manufacture of injection molds, primarily for the automotive, aerospace, entertainment, and electronics industries.

ATEMIP is specialized for over 30 years in thermoplastic injection parts or assemblies with strong technical constraints. Machine park 43 presses 35T to 350T.

Founded in 1989 thanks to the brothers Luigino and Sante Cippitelli, Italmetal specializes at first only in the production of buckles and metal accessories for leather goods, quickly establishing itself as an important supplier for several national and international companies. Parallel to the production of accessories for leather goods, the company gives life to a technical department of design and development CAD-CAM for prototypes and moulds in steel, reaching important positions also in the production of technical details in zamak, in particular for the industry of furniture, automation and accessories. Currently the company, spread over a covered area of 5,000 square meters and with a workforce of 40 employees, is able to provide a complete service that goes from the study of the product up to the production of the same, passing through all the phases of the process work, which are carried out almost completely within the company itself. The types of processes that Italmetal can offer are almost exclusively addressed to the injection moulding sector. The two main production sectors are: Design and production of injection moulds for zamak and plastic materials. In the various phases that constitute the birth of an egg produced, the realization of the mould represents a crucial moment that will influence all the subsequent production phases of the product. The Molds department designs and manufactures moulds both for third parties and for internal needs. The department consists of a technical office that analyzes and studies the equipment commissioned to verify the times and technical specifications, and a modern workshop that follows all the construction phases. Together with the Stamping department, it carries out the testing of the equipment made up to the final set-up. Zamak moulding. The Stamping department, in addition to testing the equipment produced by the moulds department, takes care of the moulding and all the subsequent processing steps to which the parts are submitted before delivery. The technologies used in the department are two, by die-casting and by centrifugal moulding. Die-casting is used for the production of parts with high runs and for the production of technical parts with reduced dimensional tolerances, the centrifugal moulding is used for the realization of medium / small series and "pilot" parts. In almost 30 years of activity in the field of accessories production, the company has gained experience and expertise in the matter to be able, for each new project, to define with accuracy and safety the problems that may occur in the various production processes and consequently, advise the customer on the most suitable solutions to simplify or prevent these problems. Our strong point is this, a deep knowledge of the problems related to the development of new products, supported by years of experience and the use of the latest technology, which allow us to solve technical problems before the launch of the order and update our customers in real time already in the pre-industrialization phase of the product.

RUCO - The ideas company Creativity - made in Germany - is our strength. RUCO is a German family-run manufacturing enterprise with more than 30 years of experience that is famous for its innovative and practical household, home living, kitchen, bathroom and garden products. We develop intelligent and high quality solutions that help to simplify and organise people's everyday lives. So why not try us out?

Plastic Injection Moulds Manufacturing

KERO AG - innovative and customer-oriented For over 30 years we have been developing and manufacturing plastic parts of all kinds for our global customers from all industries. Thanks to our expertise and continuous investment in the most modern manufacturing processes, we are your guarantee for the highest quality at competitive prices. With us you get everything from a single source, from the project to the finished plastic part. You benefit from over 25 years of experience in plastic injection molding and mold construction, paired with the latest specialist knowledge, flexibility and the highest level of quality awareness. If necessary and useful, we can fall back on a large network of specialists. This enables us to offer our customers tailor-made solutions at affordable prices. Our sustainable production is characterized by the constant improvement of work processes and the careful use of our resources. This enables us to secure numerous jobs for the future. KERO AG is your reliable partner!

We are an international tool manufacturer for processing 2k, compound or pure LSR as well as elastomer tools

Plastic injection mold

Our core business is design and manufacturing of injection moulds for pallets, bulk bins, waste containers, crates and medium-to-large parts for other applications. Here you can watch our company video: https://youtu.be/MVRRBtNxbj8 Highlights of our company: -since 1982, more than 2000 moulds built for products weighing from 500 grs up to 40 kgs -100% production in our two plants in Jesi -Customers from 35 countries all over the world -High flexibility and easy communication thanks to a lean structure -Product design, injection moulding analyses, reverse engineering, prototype moulds ecc. -Trials in our factory on machines from 750 T to 4800 T -Assistance during start-up at your site -Service and repair, also at your site, also on moulds built by other moldmakers

Sedlom specializes in the design and manufacture of precision technical molds for the plastics industry, located in Marinha Grande, Portugal The molds produced are mainly intended for the automotive industry, home appliances and electronics. 90% of them are for export. We obtained the Status PME Lider in 2014, 2015 and 2016 in recognition of its excellent performance.

The company has been pursuing the goal of being the best since its establishment in 1975. 2021 27 employees 17 plastic injection molding machines 6 ultrasonic welding machines 5 million euros of annual turnover 46 years of tradition

The company Apocer, Lda was founded in Pombal (Portugal) in 1980, as a result of the need for technical solutions for industry. Apocer, Lda started its operations by producing moulds for tile pressing and rubber overmoulding (engine support) for Delphi Portugal and USA . Over time, and following the decline of the construction market, we have expanded our manufacturing range to include the production: *Cold Runners for rubber, *Moulds for rubber parts, *Dies for the extrusion of plastic granules (compounding), *Small and medium sized manufacturing of metal parts.