The technical capabilities of the WP hydraulic cutting technology: • Water jet cutting in 2-D (Including systems with up to 6000 bar and angle correction) • Water jet cutting in 3-D • Prototype • Custom • Design and construction of devices • Preparation and processing of CAD data What materials we can edit? • Rubber profiles • Plastics • Foam • foam rubber • Aluminium • Steel • Stainless steel • Titanium • Copper • CFRP • GRP • Marble • Stone • Acrylic • Glass • Special materials • and much more What are the advantages of water jet cutting? • Materials can, in contrast to all other separation methods to a thickness of 100 - 150 mm are processed • Cost-effective low-volume or prototype production • Economical separation process (no tool change, simple devices, no clamping devices) • Low program creation time • Cold cutting process (no thermal and chemical changes / change in the microstructure of the material, thus no material distortion) • Multiple operations (suchAs notches, holes, figure and contour) can be cut in one step • Scratch-free processing of the surface • No generation of toxic gases or vapors • no development of dust, chips or smoke • environmentally friendly separation methods (the use of natural substances such as water and sand) • high precision • No part warpage (except where appropriate material residual stress) • Processing option for (almost) all materials (even wrmeleitende or reflective materials) • Good cutting ability for composite and fiber-reinforced materials, suchB. sandwich materials such as CFRP or GFRP • No deformation of the material by pressure in the cutting area (only one cutting pressure of approximately 40 N on the workpiece) • No violation of the material surface (no hairline cracks in the cutting area) • Complex shapes are cut with high precision • clean cut edges without fraying and only with minimal burr • Filigree cut designs with fine contours and minimum bridge widths are technically feasible • Low material loss and waste (less kerf and optimizing material utilization) • Small cutting gap (in clean water 0.06 to 0.3 mm, using abrasive from 0.76 to 1.2 mm) • Cutting of any possibility, even complex contours and shapes, sharp angles, oblique cut edges and small inner radii • cutting ability in all directions • section may use or end at any point of the workpiece What speaks for the WP Hydroschneide technology

SPR GmbH is a service provider for the production of turned and milled parts and your reliable contract manufacturer! The strengths of our production lie in the production of individual parts and small series. Regardless of whether it's turning, milling or turn-milling combinations, our machinery allows us to be very flexible for you. The maximum travel distances for milling are 1,100 x 600mm and with 5-axis simultaneous machining, we can process workpieces of up to 1.2 tons. On our lathes, we can produce chuck parts from the smallest diameters up to Ø800 mm. Shafts up to Ø500 mm and a length of 2000 mm can be produced. We have had our quality standards certified in accordance with ISO 9001:2015 with our QM system!

Automation from batch size 1 With more than 12 years of experience in the field of process development, ID: Industrial Dynamics GmbH is your partner when it comes to further development | Optimization of existing as well as the development of new manufacturing processes. With the "keep it simple, flexible and efficient" philosophy, we design trend-setting lean processes and convert process requirements into flexible solutions that focus on your product. Using the latest technologies, such as robotics, industrial camera systems and sensors, we plan and implement your processes. As a system integrator with experience, passion and professional competence, we take care of your questions.

MG CONSTRUCT d.o.o. is one of the Croatian companies in the metal industry, specializing in the production and assembly of a wide range of products with a focus on metal structures. We deal with the processing of steel, stainless steel and aluminum. The goal of MG CONSTRUCT d.o.o. is to provide our clients with flexible service and efficient implementation of their projects, to be a responsible employer and partner to its employees.

Facts: The BB machining is a wage rotary company with about 15 employees. With core expertise in the flexible and customized manufacturing, we always strive to ensure our customers high process reliability. Our rotating parts can be found everywhere, where high precision is required. From writing instruments to the furniture, in the control, control and drive technology, tool and model as well as in general engineering to optical industry or even in medical technology. There are lots of industries that we serve. Their development and construction Your purchasing and quality management takes with us coherent solutions to implement your requirements. Options: Produce Multifaceted rotating parts, is for us an everyday task - our ranges of rotation • From about Ø 3 mm up to Ø 32 mm from the rod • Maximum length 300 mm • 6 kt. 3-27 mm Further processing: Post-processing such as grinding, Trovalieren and Diamantiern are of course possible.For heat treatments and surface finishes are our competent partner companies. Materials: We manufacture simple and complex precision turned parts in virtually all materials, including: • All Al-Si alloys and in particular • Stainless steel (VA) steels • construction, deployment, remuneration, nitriding steels and tool steels • Brass, bronze, copper, etc. • Titanium alloys • plastics such as POM or PEEK Other materials? Ask us! Batch sizes: Both simple and highly complex parts are produced in our home always from the perspective of economic efficiency. • Small to medium batch sizes from lot size 1 possible • small series up to 50 pieces • Small batches of 50 to 500 units • and medium runs up to max. 100,000 Quality: Quality and reliability of our products are reflected in the satisfaction of our customers and created on the basis of a modern quality management system certified according to DIN EN ISO 9001:2000. For the implementation of the clear objectives of management, a holistic and integrated manufacturing and inspection planning and continuous monitoring of the entire process is guaranteed by two specially trained staff. This assures you a highest quality standard from the home BBZ.

I am Kornél Ledniczki, managing director and co-owner of Stahl CNC Hungary Kft. Karl Stahl and I founded the company in 2015. I worked for him in Germany until 2015, and that's how the idea came up to set up a joint company in Hungary. Since then, we have already found many satisfied Hungarian, German, Austrian and Belgian partners. Once we have met our deadlines, we can meet our deadlines almost 100%, and the components we produce must not only be good, but also beautiful.

H7/h6 OÜ is an Estonian precision engineering company producing precision-machined components from a wide and diverse range of materials.

Frech Drehteile GmbH has been your competent and efficient partner for high-quality CNC turning and milling work from all common machinable materials since 1980. Innovative thinking, growth and continuous modernization characterize our company. This combines the flexibility of a family business with the performance of a medium-sized company. The company was founded in 1980 by Franz-Xaver Frech. Constant expansions and relocations to larger production halls made it possible to satisfy growing demand and turned the small business into a medium-sized company, which is now run by son Patrick Frech in the second generation.

We are a family-run company with a long history that is characterized by innovation and the use of the latest machine technology. We are currently experiencing a generational change, with our tradition of quality and passion for excellence passing on to the next generation. Our commitment to innovation and the use of cutting-edge technologies remains the key to success.

What happened in 2004 with the introduction of precision turning parts for automobile shock absorbers, we have developed purposefully and consistently until today. In doing so, our strengths and services rest on a broad-based, interconnected network of partner companies with the widest range of manufacturing technologies The entire spectrum of special and drawing parts is available and subsequent actions. Through our special focus on these areas, we efficiently bundle synergies and create cosmetic benefits for our customers. MAGRO serves customers, both from the automotive industry and machinery & an¬la-engineering, as well as from railway technology, vehicle construction, crane & lifting technology, for agricultural & construction, as well as logistics & warehouse technology NiK

In addition to standard metal construction manufacturing processes, we are a certified welding and gluing specialist for rail vehicle construction and offer our customers complete assembly production including coating. We process steel (max. 25mm), stainless steel (max. 20mm) and aluminum (max. 12mm) and are mainly active in the thin sheet range up to 6mm. Our main areas of business are sewage/environmental technology, rail vehicle construction and electrical plant engineering. To meet the diverse requirements of our customers, we have a broad network of suppliers for machining and surface treatment, for example.

Producing equipment, tools and machine parts to the assembly, milling on 5 DMU70 Evolution 5-chsigen milling machines, also incl CAM free surface machining. Our main area: Werkstückträgervorichtungen for the automotive industry and components for the corresponding plant.

Manufacturer of injection molding tools 1 to. up to 60 to. multiple cavities 1K, 2K, 3K Mucell and SGI

WiggenTech GmbH is an owner-managed family company based in Lippstadt. Our company focuses on the development, production, coating, trade and sale of fasteners for customers in the industrial and automotive sectors. WiggenTech GmbH successfully became independent by spinning off the in-house turning and drilling company of Hella Kg.a.a. as part of a transfer of operations in accordance with §613a in 2021. As a “start up”, we can therefore already draw on decades of “know-how” in the production of complex fasteners. Every year, we produce around 15 million precision turned parts, which are used as fasteners by various vehicle manufacturers, automotive products and in industrial applications. We are particularly proud of this. With their expertise and innovations, our employees form the foundation of the company and guarantee our current and future success.

Why you are right with Schneider turned parts? Because we are already on the market since 1952, we continue to evolve, have a small staff to respond quickly enough and skilled workers to deal with all the requirements of our customers always meet. Long-term business relationships prove that our performance fit. What Schneider turned parts for you making? We manufacture long turned parts up to a diameter of 38 mm and a length of 1000 mm, also short turned parts up to 60 mm in diameter made of aluminum, copper, steel, stainless steel, brass and plastic. We milling, drilling, grinding, pressing. Here we are, we specialize in medium and large series. The finished parts are available either completely or we store them in our computer-controlled warehouse for you. We work with a modern equipped PPS and MDC system and put all the tasks required by our customers to quickly and effectively, eg consignment stock, Kanban deliveries or dial-up calls. What else is there interesting about Schneider turned parts? Our skilled professionals, we form largely from themselves and develop them to professionals so that we can meet customer requirements in the future. Already experienced in training as a machinist and experience our employees, our customer orientation. With our modern heat exchangers, we use the waste heat from the engine to heat the production halls, which saves us operating costs and helps the environment. With flexible employees in multiple shifts we can keep delivery times short and absorb demand peaks.

Hilger GmbH works as a developer and supplier for machinery and Plant construction and the automotive sector. The areas of work include Development and production of individual and series parts up to batch sizes of one million, the development and construction of prototypes and assemblies, and assembly work. In over 30 years, Hilger GmbH has been able to develop extensive core competencies in develop respective areas. The work is characterized by the integrated product development. Direct collaboration between development and production enables cost-effective product development, low production costs and high product quality when entering the market.

Welcome to the UF Industries GbR. For more than 20 years, we have been bundling the necessary skills for everything to do with drawing parts in a separate department. Our employees advise and support you in the procurement of tailor-made special and drawing parts and produce high-quality and precise turned, milled and combination parts for you according to drawings - even in demanding geometries and in small batch sizes. Quality and function are our top priority. In order to achieve this, we are constantly developing ourselves and our portfolio. True to the motto: If you stop getting better, you stop being good! Our aim is to be able to offer an efficient and optimal solution for every specific, mechanical-technical requirement based on a drawing or sample. If required, we offer you fast and goal-oriented support in the realization of your constructions. Especially in the project phase, it is of crucial importance to choose the best, most modern and at the same time most cost-effective production technology. We would also be happy to optimize existing construction parts together with you.