The technical capabilities of the WP hydraulic cutting technology: • Water jet cutting in 2-D (Including systems with up to 6000 bar and angle correction) • Water jet cutting in 3-D • Prototype • Custom • Design and construction of devices • Preparation and processing of CAD data What materials we can edit? • Rubber profiles • Plastics • Foam • foam rubber • Aluminium • Steel • Stainless steel • Titanium • Copper • CFRP • GRP • Marble • Stone • Acrylic • Glass • Special materials • and much more What are the advantages of water jet cutting? • Materials can, in contrast to all other separation methods to a thickness of 100 - 150 mm are processed • Cost-effective low-volume or prototype production • Economical separation process (no tool change, simple devices, no clamping devices) • Low program creation time • Cold cutting process (no thermal and chemical changes / change in the microstructure of the material, thus no material distortion) • Multiple operations (suchAs notches, holes, figure and contour) can be cut in one step • Scratch-free processing of the surface • No generation of toxic gases or vapors • no development of dust, chips or smoke • environmentally friendly separation methods (the use of natural substances such as water and sand) • high precision • No part warpage (except where appropriate material residual stress) • Processing option for (almost) all materials (even wrmeleitende or reflective materials) • Good cutting ability for composite and fiber-reinforced materials, suchB. sandwich materials such as CFRP or GFRP • No deformation of the material by pressure in the cutting area (only one cutting pressure of approximately 40 N on the workpiece) • No violation of the material surface (no hairline cracks in the cutting area) • Complex shapes are cut with high precision • clean cut edges without fraying and only with minimal burr • Filigree cut designs with fine contours and minimum bridge widths are technically feasible • Low material loss and waste (less kerf and optimizing material utilization) • Small cutting gap (in clean water 0.06 to 0.3 mm, using abrasive from 0.76 to 1.2 mm) • Cutting of any possibility, even complex contours and shapes, sharp angles, oblique cut edges and small inner radii • cutting ability in all directions • section may use or end at any point of the workpiece What speaks for the WP Hydroschneide technology

The AWM AG operates in two sectors: 1. Production of injection molds with max. 10 t and max. dimensions 14500x1200x1200 2. special purpose machines (manufacture of automatic assembly machines) Technical specifications: 145 employees Performance EUR 13-15 million (share Sondermaschinenbau 60%) Share capital 500 thousand Property surface 24000 m² Translation by Google Translate

SSI Schäfer s.r.o is a long-standing supplier in the areas of cabin construction (sheet metal enclosures), welding components including mechanical processing and painting, and component assembly. In Hranice, we process approx. 32,000 tons of steel per year on 75,000 m2 with just under 1,100 MA.

Production of precision parts. Machine's components. Entire groups and complete machines. Prototypes and small series. Work in any kind of materials and surface treatments.

MBT Frankenberg GmbH is a competent partner in stainless steel processing and bending technology. The company manufactures precise components and assemblies to customer specifications and stands for reliable quality and clean workmanship. In the field of bending technology, its range of services includes in particular mandrel bending, ring bending, helical bending, and profile bending—delivering accurate solutions for a wide variety of applications and industries.

Automation from batch size 1 With more than 12 years of experience in the field of process development, ID: Industrial Dynamics GmbH is your partner when it comes to further development | Optimization of existing as well as the development of new manufacturing processes. With the "keep it simple, flexible and efficient" philosophy, we design trend-setting lean processes and convert process requirements into flexible solutions that focus on your product. Using the latest technologies, such as robotics, industrial camera systems and sensors, we plan and implement your processes. As a system integrator with experience, passion and professional competence, we take care of your questions.

The Kurt Eckstein GmbH manufactures since 1973 blanks in general structural steel. First was produced with conventional cutting machines. Due to the requirements of the cut part, we quickly realized That has to be invested in CNC machines. Claims to material - cuts that are caused by thermal processes, or not to cut, we have, in 1994, the water jet cutting technology integrated into the production line. Today autogenous flame cut, water-jet cuts and laser cutting are manufactured on modern equipment. For over 30 years satisfied customers. Quality, reliability and on-time delivery are our principles. Thus, we have earned the trust of our customers, who come from diverse areas of industry, crafts and trade. Technological advantages waterjet cutting • no mechanical and thermal damage to the cut surface • good use of material • cutting any contours • Minimal pressure on the workpiece • Unlimited variety of materials • Painted and coated parts can be easily edited Large water-jet cuts Appendix 1 - T11 2060 - Work area 2000 x 6000 mm - Water jet cutting with two heads Water jet cutting with cutting bevels - compensation Appendix 2 - WMC2 4030 - Dynamic - Work area 4000 x 3000 mm - Water jet cutting

Industrial technology, mechanical engineering

We have been manufacturing large mechanical parts of up to 20t since 1946. Our core competencies include milling, turning and grinding. We process a wide variety of materials such as steel, chrome steel, aluminum, titanium, bronze or plastic. With our creativity, we deliver sophisticated individual parts as well as small and medium-sized series quickly, precisely and economically. Ask us: We look forward to providing you with competent, professional and uncomplicated support.

We produce holistic solutions together with our customers. We are your specialist for sheet metal parts made of steel, aluminum and stainless steel: - Stamping - Lasers up to 2 x 4 m and a thickness of up to 30 mm - Edges of up to 6 m and a thickness of 12 mm possible - Deep-drawing is possible for larger quantities From 1 to 500,000 pieces, we produce everything for you with love. A second heart beats in our chest. We are also one of the oldest HPL dealers in Germany: - Cut to size from HPL according to your wishes - Milling almost anything you want - Sandwich panels made of various materials for you. We work according to the principles of DIN ISO 9001:2000 even though we are currently applying for a new certificate. We are happy to be there for you. Just give us a call at 0931/40664-0 or anfrage@roehl.de. Best regards Your Röhl team and the Röhl family

When welding processes, our company offers the manual metal arc welding processes (111), metal active gas welding (135) as partially or fully mechanical process and tungsten inert gas (141) at. Processed materials are steels of material group 1.1, 1.2, 1.4, especially non-alloy structural steels according to DIN EN 10025, ie from S235JR S355JR up. Also aluminum structures can be produced. The processed metal thicknesses range from 3 - 50mm. The cutting of sheets or profiles mechanically (saw cut, hydraulic and manual scissors), thermal (oxy-fuel cutting) as well as subcontractors optically possible (by laser). Before welding processing of sheet metal they can be Transformed cold (edges, rolling). Lifting devices (2 x 8t, 10x1t / 0.5 t) in the form of cranes are available. Deformation of welded components can be compensated with the process autogenous flame straightening. The working areas of the metal glasses with the general steel construction with approval for crane rails and steel structures as well as the production of traffic signs bridges according to ZTV-ING part is prescribed 9, paragraph 1.

H7/h6 OÜ is an Estonian precision engineering company producing precision-machined components from a wide and diverse range of materials.

ZIEGLER – a successful family business for three generations, with headquarters in Bavaria and a manufacturing facility in Daugavpils, Latvia. ZIEGLER manufactures to order according to customer requirements and project specifications. We also offer our customers material procurement for their specific projects: welded assemblies, bent parts, assembly work, painting, and logistics.

The company developing and manufacturing Eßbach was founded in Berthelsdorf 1999. Since April 2007, we relocated our headquarters to Brand-Erbisdorf. Here are covering an area of 750m ² various machining centers, design workstations and above average well-trained staff available with which we can also realize your tasks! Our high quality standards are certified by our certification to DIN ISO 9001. Examples of our products you can found in our website www.efe-essbach.de. Our main pillar is the development, production and distribution of heat sinks for power electronics. In addition to liquid cooling body systems based Unicool we also manufacture air-cooling systems of the body or combined devices after the system coldplate. Of course, we adjust the devices on your required specifications. Customers who use our products or benefits, include Siemens, Bosch, Baumuller, Bonfiglioli Vectron GmbH and Lust Antriebstechnik GmbH. In addition to the production of heat sinks, we operate a small special engineering. With this we are able to manufacture high quality facilities capable of over CAD design and CAD / CAM Interfaces. Thus, several different labeling systems to the standard product labeling including PDC connection were realized in our home. The investments are made entirely with control, and CNC-axes and delivered. Our customers can be found among others in the field of automotive and supply industry. Examples are: - Test benches for drive spindles with data acquisition - Labeling systems with freely programmable CNC axes 800x600x400 - Marking gear parts with interface to the PPS system - Devices for assembly and testing purposes - Molds for aluminum cast parts up to sizes of 800mm, including processing of castings when required - Special coolant systems for machine tools With our technology, we are able to realize customer-specific solutions, including the manufacture of parts and assemblies.Our machinery, we have expanded to operate and in particular the following machines: - 1 CNC machining centers with tool change 2000x800x800mm, internal cooling and swivel head - 1 CNC machining center 1000x500x400mm with tool changes and internal cooling - 1 CNC machining centers with tool change 500x400x400mm and NC rotary table - 1 universal CNC milling machine 800x400x400 (vertical and horizontal) - 1 CNC lathe, diameter 300mm long and 300 - Conventional turning up to 1000mm long - NC mandrel tube bending machine to D 26x2mm VA tube - Korundstrahlkabine for VA materials - Edelstahlbeizeinrichtung inside and outside - TIG welding workplace The CNC machines are connected to our CAD / CAM system and thus to work in a position to meet your or our drawings. Again, we have customers such as Heidelberger Druckmaschinen AG, Deckel Maho, Samputensili GmbH, Bharat Forge Aluminum GmbH & Co.KG or Licatec GmbH.

Our company was founded in 1925 in Hamburg We have focused on the production of Specialized extruded profiles and components for small and medium-sized companies in industry and crafts. Our customers appreciate the fact that, in addition to manufacturing profiles, we can also offer processing according to customer drawings. We offer a wide range of processes: from lasers to milling, turning, drilling and even the assembly of components. If you are looking for a professional team to implement your ideas at optimal conditions, then get in touch with us. We become a trustworthy and competent partner for our customers, providing support in development and production in fair and open cooperation.

Paul Brüser GmbH is a medium-sized family business based in Sauerland. Whether punching, drawing or welding, plastic injection molding, tool and prototype construction, Paul Brüser GmbH is your reliable partner. Our experience in a wide range of areas pays off. Through metal processing, plastics processing and component manufacturing as well as our own tool making, we manufacture products individually and flexibly according to your requirements. What you can expect from us: Flexibility — In any situation, we are happy to adapt to the tasks you have set and can develop qualified solutions. Quality — Strict controls ensure the safety and quality of our products. You can rely on our work. Service — We are always open to your concerns and wishes and provide you with efficient and professional advice on the implementation of various concepts.

Located in Moutier, in the Swiss Jura, an area with a rich history in the machine tool and precision turning industry, Ricci & Mottaz leverages its expertise to produce high-precision components. We offer a wide range of products that meet the requirements and expectations of each customer. ISO 9001 certified, we are continuously committed to improvement and place customer satisfaction at the heart of our concerns. Our commitments: - Excellence and Precision : We pay meticulous atention to detail - Rigourous control : We implement strict quality control of parts before shipment - Partnership spirit : We value your feedback and are committed to continuously improving our services to better meet your expectations and anticipate future needs - Innovation : We provide tailor-made solutions to support our clients in their projects - People and culture : We emphasize human values, fostering a collaborative and respectful work environment

We are a second-generation injection molding business with a 52-year background and over 25 years of know-how in reversible multi-cavity insert integrated proprietary optical gate nozzle hot runner mold bases; this technology allows customers to reduce mold base cost, engineering time, and CNC workshop load time. The entire mold base system and inserts to hold multiple simultaneous and mixed cavities can be custom-designed to suit the customer's dimensional item average dimensions, allowing the customer to recycle mold bases over the years. With our technology, we have been able to produce parts with thicknesses as low as 0.7 mm in 4.5-second cycles, operating at a temperature of 18°C. Cycle times can be further reduced by using more efficient injection molding machines. Of course, the geometry and thickness of the part impose certain limits.

CM S.r.l. is an Italian company, which was founded in the 60s as a precision turnery. Over the years the company has specialized in the production of coaxial connector / cable for radio frequency. CM Srl covers a premises of 3,000 square meters and employs 50 people. CM Srl operates as the parent company in the manufacture and sale of coaxial connector / cable and cabling; this has been a subsidiary the SIMM Srl, which has continued its activities in the field of origin mechanical machining, in particular turning and milling. The SIMM Srl operates not only traditional materials such as brass, steel and aluminum, but also such as Beryllium-copper alloys, and invar. We are also active in the processing of plastic material such as PTFE, POM, rexolite and Ultem.