Manufacturer of precision turned parts with hardened and ground surfaces.

Steel is our lifeblood - that's us LSV Lech-Stahl Veredelung GmbH was formed from two traditional bright steel companies in 2012. Lech-Stahl Veredelung in Oberndorf am Lech and Stahlveredelung Landsberg (SVL) have merged to form LSV Lech-Stahl Veredelung GmbH based in Landsberg am Lech. To implement new technologies, another location was built in the immediate vicinity of the parent company Lech-Stahlwerke in Meitingen in 2019. LSV Lech-Stahl Veredelung GmbH is a 100 percent subsidiary of the only steelworks in Bavaria, Lech-Stahlwerke GmbH in Meitingen. Both companies are part of the Max Aicher Foundation group. Our parent company is one of our largest suppliers of raw materials and supplies us with steel made from 100 percent recycled scrap. Due to this corporate structure, it is possible for us to fall back on the entire value chain and the associated expertise. The approximately 300 employees at the three LSV locations are committed people who are passionate about it. Decades of experience in the production of bright steel and the refinement of steel as well as the pursuit of the highest quality make it possible to realize the wishes of our customers and to establish close customer loyalty. Passion also means reliability paired with qualification. Therefore, in addition to the technically sophisticated production facilities, our employees are the basis for our success. LSV location Landsberg am Lech headquarters At the location in picturesque Landsberg am Lech, over 50,000 tons of bright steel are produced annually in a wide variety of refinement and processing stages. The focus is on the production of high-precision and ground toothed rack blanks as well as inductive single bar tempering. In addition, there are all classic bright steel processes at the highest level. LSV location Oberndorf am Lech The tranquil Oberndorf am Lech in the Donau-Ries region is the location of a completely modernized and expanded company with a capacity of over 80.000 tons per year. A high-tech bright steel production also forms the basis for the further refinement of the products. Short piece production and tempering systems at the highest technical level enable deeper added value in the production chain. The youngest LSV location in Meitingen Our third production site in Meitingen has been in operation since 2019. In addition to an outdoor warehouse and central warehouse of the parent company Lech-Stahlwerke, we produce steel in different processing and processing stages on almost 10,000 square meters in two aisles. In addition to the most modern production lines, the youngest LSV location has a motivated and flexible team that draws on the many years of experience of the other two locations.

Ranieri is an Italian company certified ISO9001:2015, a sub supplier specialized in the production of industrial rollers: conveyor rollers, rubber rollers and cylinders. Our partners operate in different sectors such as the paper industry, earth moving machines, agriculture, wood and other industrial machines which need rollers upon technical drawing that reach diameter Ø520mm and length 3.150mm.

At five locations in Germany Herzberg am Harz Stuhr near Bremen Norderstedt near Hamburg Reinberg in Saxony Thale in the Harz Mountains, leads the group HEAT heat treatment on a broad range of technologically sophisticated products through. Clients come from the aviation and aerospace industry, the automotive industry and in mechanical engineering. Heat treatment on a large scale and important contributions to the optimization of the performance features delivers the HEAT Group for the automotive industry in the areas of: - Passenger restraint system - Diesel injection systems - Suspensions - Drive Technology

Our enterprise is a private company which continues the 25-year tradition of clutch and brake production in Ostrzeszów, Poland. The company was established in 1993. We employ a highly qualified staff of over a hundred and have our own research and development base. We manufacture a wide range of controllable clutches and brakes used in machines and appliances in various branches of industry. We also cooperate with major German enterprises in this regard. In order to guarantee high quality of our products and meet our customer's needs, we implement the ISO-9001:2000 quality system confirmed by a certificate obtained from DQS. Range of services offered by FUMO–Ostrzeszow: 1. Machining: • Turning: Dmax = 560 mm; Lmax = 900 mm; weight max 100 kg • Milling: Lmax = 1000 mm; Smax = 1000 mm; H max = 1000 mm; weight max 500 kg • Straight teeth chiselling: Dmax = 500 mm; Lmax = 90 mm; module mmax = 5 • Grinding of holes: Dmax = 120 mm; Lmax = 160 mm; weight max 25 kg • Grinding of shafts: Dmax = 150 mm, Lmax = 500 mm; weight max 25 kg • Locksmithery and fitting, including the winding of coils of self-baking wire: coil wire dimensions: D=0,15÷1,40 coil dimensions Dotw 25÷200; L = 10 ÷ 80 mm 2. Heat Treatment: • Hardening of pieces in the electric tunnel furnace with ZAS III protective atmosphere piece flank Lmax = 450 mm lub D max = 450 mm; thickness 0,5 ÷ 6,0 mm; weight max 4 kg • Annealing, hardening, tempering in furnaces without protective atmosphere SQ310 • Induction hardening with UNITERMA–60 system 3. Thermochemical Treatment: • carburizing 4. Chemical Treatment: • phosphating of pieces coat thickness 0,003 ÷ 0,005 mm • blacking 5. Plastic working: • die shearing, stamping, tonnage capacity of the press: 16; 100; 400 tonnes 6. Tool Shop Work: • Manufacture of technical instrumentation • Manufacture of plastic working instrumentation: blanking dies, stamping dies, etc.

MDL is the long-standing supplier of standard parts and stamping Standard components for tooling and mold. Our product range includes cutting elements, guide elements, column guide frames, gas struts, coil springs and elastomer springs for tool and mold making. We also supply a wide range for a toolmaker. MDL has an extensive and modern machinery to quickly and cost-effectively perform CNC Milling for you. As a contract manufacturer, we are able to supply machined parts as individual parts and small series for them. Our product range includes glow, surface grinding, 5-axis milling, high speed milling Stress. In addition, we provide precision turned parts by centerless grinding, CNC grinding, high speed turning, Drahterrodieren and Senkerrodieren.

A. WENZLER GmbH & Co.KG has produced precisely engineered turned parts for industry since 1962. The company is considered to be one of the leading partners in the automotive and medical technology sector. When Jens Kurzhals, machine operator at Wenzler was interviewed, he said: "Our pieces are not supposed to be good, but excellent.“ He only needed a few words to sum up the philosophy of the company steeped in tradition: We want to move the world forward a little bit with every turned part. s t r u c t u r e: Size of operation: 42 employees, breakdown: 30 in Production, 4 in Administration, 3 in Quality Assurance, 5 apprentice (cutting machine operator) QM System: Certified according to ISO 9001:2002 and ISO/TS 16949:2002 Sales in 2008: 5.0 million Euro Investments 2008: 1 million Euro p r o d u c t i o n: Materials Free cutting steel, case hardened steel, structural steel and tempering steel, rust and acid resistant steel as well as extrusion metals such as brass, copper, aluminium and titanium Further processing Polishing, honing, deep hole drilling as well as all kinds of thermal and surface treatments

The company Frentech Aerospace sro, now one hundred percent in the Czech owned, was founded in 1994 to be with the aim to become a qualified and competitive suppliers in the field of precision engineering. Initially, the products were targeted in the field of medical technology, microelectronics and special machines, including the delivery of spare parts.

Since 1952 WSK "PZL- Kalisz" S.A. has been representing Polish aircraft industry and manufacturing aircraft piston ASz-62IR and AI- 14R engines. They are designed to power the following airplanes: An-2 and M-18 “Dromader" (ASz-62IR) and respectively PZL-101 “Gawron” and PZL-104 “Wilga” (AI-14R). These engine types have been worldwide recognized for their quality and awarded numerous quality certificates issued in the USA, Canada, Brazil, People’s Republic of China. They have been produced in thousands and have proved failure free thus clearly evidencing their highest reliability and performance quality. WSK “PZL-Kalisz” S.A. also overhauls and performs repairs of ASz-62IR and AI-14R engines. In addition, the Company manufactures and repairs assemblies and parts of TWD-10B engine for An-28 aircraft. WSK “PZL-Kalisz” is a joint-stock company (own capital is 85 mln PLN and paid-up capital is 45,86 mln PLN) operating on the basis of the Commercial Company Code. Principal shareholders of the Company are as follows: - Industrial Development Agency 75,45% - Company employees 11,59% - SEMA Sp z o.o. 6,25% - the City of Kalisz 1.35% - Energy Plant "Energa S.A." 1,20% - Other shareholders 4,16% WSK “PZL-Kalisz” is a capital group composed of the mother company and its 2 fully-controlled subsidiaries: - ZOT “NARZĘDZIOWNIA WSK” Ltd. - PPUH „MECHANIK” Ltd. WSK „PZL-Kalisz” S.A. is the company of the essential importance for the Polish economy and is considered as part of the Polish Defence Industry Potential. As a result of the Company's restructuring process WSK "PZL- Kalisz" S.A. has extended its business into wide range of manufacturing programs and servicing activities including production of high pressure engine parts, oil pumps, gears, aircraft screw gears, turbochargers, push rods, pump housings and first of all crankshafts for high pressure engines. All these components require high precision machining in performing special requirements of its customers. WSK "PZL-Kalisz" S.A. maintains business relationship with well-renowed companies such as: General Electric Transportation Systems, Allison Transmission, Turbomeca, Sulzer Textil Switzerland, Pratt & Whitney Kalisz, and many others. Part of the Company production is designated for military aviation. The Company aim and priority is focused on meeting the Customer’s requirements that can be with WSK "PZL-Kalisz" capacities. WSK “PZL-Kalisz” S.A. acquired modern machinery operated by highly qualified and experienced technical staff. The Company continuously seeks new Customers and Suppliers especially in the manufacturing of precise and aviation components requiring high precision processing. Interested partners are always welcome. In 1999 the Company was awarded ISO 9001-2000 Certificate. In 2000 the Company was granted PART-145 Certificate. The following year – 2001, the Company attained PART-21G Certificate. In 2002 the Company was awarded AQAP-2110 Certificate. In 2004 WSK “PZL-Kalisz” S.A. was granted a license by The Polish Ministry of Internal Affairs and Administration for manufacturing and trading products and equipment for military and police force application as well as transfer of technologies. In 2009 the Company was awarded AS 9100 Certificate.

h2> Success- now and in the future /h2> Through continuous development over the past 75 years, Charles Scharrenbroich GmbH & Co. KG has grown into a high-tech oriented company. Since then, this name stands for the production of high-precision and precision cut parts and components for axles, steering, transmission and aggregates of various kinds of high quality. Our customers include well-known European manufacturer and supplier of automobiles, vehicles, transmissions and engines.

INDUSTRIAS ALZUARAN, founded in 1959, is a spanish ISOTS16949 certified company dedicated to the manufacture of stamping parts with heat treatment, such as retaining rings DIN-471,472, 6799 spring washers DIN-2093, safety washers DIN-7967, wave washers, clips,.. etc…and special parts according to drawing or sample up to 6 mm in thickness. Our main customers are related to automotive industry, locks, home appliances, windmills, electric market, machinery and hardware distributors. Our export percentage is around 35% to many different countries such as Germany, Austria, Belgium, Brazil, Colombia, South Korea, Czech republic, Denmark, Dubai, France, Holland, India, United Kingdom, Israel, Italy, Japan, Morocco, Mexico, Norway, China, Poland, Romania, Singapour, Slovakia, South Africa, Sweden, Turkey, USA, Venezuela ..etc… You can find further information, visiting our web page www.alzuaran.com If you are interested in our products, or want technical advice, you can submit your enquiries to j.a.barrenetxea@alzuaran.com, and we will kindly answer you.

The vital link Operating an international network of facilities and serving a wide range of industries including aerospace, defence, automotive, power generation, oil & gas, construction, machine building, medical and transportation, Bodycote is the world’s largest and most respected provider of thermal processing services. These services are a vital part of any manufacturing process and include: - Heat Treatments - Metal Joining - Hot Isostatic Pressing - Metallic, Ceramic, Cermet and Organic Coatings Thermal processing is a vital part of any manufacturing process and includes a variety of techniques and specialist engineering processes which improve the properties of metals and alloys and extend the life of components. Without heat treatment aircraft engines would not last a single flight and car gearboxes might only last a week – if you were lucky. Without hot isostatic pressing the risk of catastrophic breakdown of metal components would be far greater and the carbon footprint of power stations would be dramatically higher. Without coatings, construction fixings would rust away and thousands of everyday objects would quickly lose their shine. Peace of mind for manufacturers for over 30 years We never forget that our customers have invested time, money and resources in all the components we process, which is why quality comes as a standard part of our service, ensuring that all our customers’ components are treated with care throughout. Our facilities hold numerous international, national and customer approvals appropriate to the services they offer and the markets they serve. Bodycote’s quality management systems, validated by major engineering OEM’s, have been developed to meet the requirements of both ISO 9001 and environmental standard ISO 14001. Additionally, market-related standards such as AS 9100 for aerospace and TS 16949 for automotive have also been incorporated. Bodycote has also gained the prestigious Nadcap accreditation at a large number of locations throughout Europe and the USA, as well as approvals from major aerospace companies and their supply chains. Additionally, our transport services are linked with process and production controls to deliver optimum logistics solutions for supply chain customers. Our customers can be confident their demands can be met, however stringent, with assured quality, cost-effectiveness and on-time completion every time.

Since 2005 we develop with our partner companies, new approaches and innovative solutions for the production of technical parts and assemblies. Our slogan "New Thinking! New action! New ways! ", We carry a competent and reliable contribution to your company's success. We advise our customers both during the product development process as well as the optimization of existing products in terms of the structural design, as well as on the use of suitable production methods and materials. We specialize in rotary swaging, spin forming, cold forging, machining (cutting all kinds), sintering, MIM, hot forging, stamping, deep drawing, sheet metal forming of all kinds, die-cast zinc, cast aluminum, cast iron, fasteners, ductile iron, cast iron and lots more! We enable potential costs through the re-design of your purchasing parts with the help of TRIZ methods, value analysis and Attributive sourcing.

Since its inception in 1999 we have specialized in the manufacture of parts and series in the area of turning and milling, and are active throughout Europe. Regular investment in new technologies and manufacturing capabilities ensure optimal quality and customer satisfaction. Good Quality begins with a high-quality production equipment, efficient processes and a clear structure. Continuous development is the foundation of our success. We employ 35 employees in administration, construction and manufacturing. Join our 4 trainees for precision mechanics and in administration. The cooperation with TME is open, direct and uncomplicated. Our clients include companies in the areas of: Engineering, tooling, laser technology, and aerospace and automotive industries. Service overview Production / manufacture of components We manufacture parts, spare parts and small series to mass production according to your drawings or a pattern. Our machining capabilities include CNC-controlled milling, drilling, turning, wire EDM, surface grinding and conventional crafts and sheet metal processing. We can use our processing centers, parts machining, up to the size: L = about 2100, W= about 1000 B =, H = about 600 and up to a weight of 6500 lbs. Construction Design of tools, fixtures and equipment. 3D modeling for prototyping. Support for design tasks and advice on cost-effective and production-oriented manufacturing of your parts during development. CAD / CAM Acquisition and processing of all popular file formats such as : STEP, SAT, IGES, DWG and DXF programming with our CAM system. Welding / Heat treatment The welding of steel and heat treatment (hardening, tempering and annealing) are also of parts of the scope of our processing. Surface treatment Surface treatments, we can perform at our partner companies. Assembly Assembly of parts, components, tools and equipment. Reports On request, we create initial sample inspection reports and test protocols. Delivery We deliver your products on time with shipping or parcel service. We are a professional partner, trust TME!

Manufacture of precision machined parts and milling parts from all machinable materials. CNC turning (up to D 90 mm rod) CNC turning (up to 250 mm in the feed) CNC long turning CNC multi-spindle turning (32 axes) CNC Machining Centers (5-Axis) Batch sizes up to 1000 pieces .... Piece including all subsequent operations up to the assembly In the field of machining there are many different ways of working. One is the CNC machining. Through this method, the milled parts get even complicated 3D contours. The CNC machining is done with machines with up to 8 axes. CNC turned parts can be made of different materials. For machining titanium, copper, brass, plastic, aluminum, stainless steel and other materials are suitable. Rotating parts in general can assume unusual shapes. In particular, the CNC milled parts often see pretty spectacular. Through its 3D contours CNC turned parts have a special effect.The machining is extremely versatile. Machining technology is used in various fields. Lathe parts, especially CNC lathe parts, are very expensive to manufacture. To produce a CNC lathe part, one special machines and more time than the normal CNC turned parts needed. The machining and especially the CNC machining requires a good education in the field. The partially very complex turned parts and just the CNC lathe parts require a tremendous expertise. A single CNC lathe part caused enormous amount of time. For these special turned parts, a particularly accurate work is absolutely necessary. For the purposes of machining are all chip forming materials. Depending on the material, the cutting is performed with different speeds. Are the turned parts made of wood, the cutting is done with high cutting speed and without cooling lubricants.Turned parts made of plastics, however, are processed at medium cutting speed. When machining water or alcohol are used for cooling. A special product from the metal cutting machines is the rotating part. Such automatic turned parts can be made from almost all machinable materials. Just like the CNC long turning parts of the screw-cutting without technical knowledge can not be produced. All machined parts require special machinery for the production. Rotating parts are to be finished by hand hardly. Are the turned parts made of wood or plastic, the machining is possibly still done manually, but with harder materials the use of expensive machining is necessary. To establish automatic turned parts, can not be dispensed with the machines. Automatic turned parts are usually ordered in enormous quantities and from extremely strong materials. Also for CNC turned parts is similar. This machining is simply too specific. CNC turned parts requiring extreme precision. Turned parts of this type are mainly used in machine and plant engineering. These industries would not do without CNC turned parts, turned parts, and the entire range of machining technology. Milling Services, CNC turned parts, turned parts, and just such special products as a CNC lathe part are absolute precision products. As simple as the concept sounds cutting, this process but it is not. Cutting sounds like simple separation that hide behind it but also things like complex CNC turned parts or automatic turned parts, no one thinks at first. Without these highly intricate parts, especially without the screw-cutting work would be impossible in some areas.

- SMK Röhrsdorf GmbH - Equipped with advanced CNC machines: - Milling up to 5 axes - Turning up to 4 axes - Milling on the Horizontalbohrzentrum - Schleifen/Koordinaten-, round, profile, surface grinding We perform CNC precision machining of metal and plastic We manufacture single and serial parts according to your drawings and samples. Be processed: - Eg steel 1.0037 / 1.0503 / 1.0570 / 1.0601 / 1.0715 / 1.2067 / 1.2379 / 1.7225 - Stainless eg 1.4301 / 1.4305 / 1.4571, Cast eg GG-25 and 0.6025 - Non-ferrous metals, aluminum, for example, 3.1645, 3.2315 / copper / brass / bronze Program of delivery - Prismatic drilling and milling parts - Turned parts Part name, among others Caliper lever / housing / cover / gripper jaws / flange / carriage / conical ring / mold core / Cam / arbor / spindle / hot runner bar / piston / sleeve / disc / grinding arbor / Cylindrical roller Heat treatment processes and surface coating Our services are completed with required heat treatment processes, forB. Carburizing, nitriding, nitro-carburizing and through the most common method of surface coating such as bronzing, galvanizing, thick-film passivation, chrome plating. - SMK V-Factory - Injection molding parts Equipped with modern injection molding machines 8 We manufacture plastic parts, from the small gear (1 g) up to the order of a panel for computer case (1000 g). Our injection molding machines have a locking force 25-420 t. They are equipped with central drying and material supply, handling systems and ink metering devices. Program of delivery It will process all commercial thermoplastic plastics. for example PP / PA 6, PA 66 (reinforced / unreinforced) / POM / PC / ABS / PE Our scope of services includes pattern pieces, small and large series and subsequent assembly work through to tailored delivery. Part name, among other things: Housing / cover / gasket / connector / File / Control / switching element / Hinges / cover / trim With our mold in the house, we can respond immediately to any changes and ensure optimal maintenance of the molds. Through our extensive range of services we are able to take on tasks from design to complete product. - SMK V-Factory - plastic injection molds We specialize in design and manufacture of plastic injection molds up to a size of 1100 mm x 800 mm x 700 mm and a weight of up to about 3 tons. With the long experience of our designers and programmers, supported by modern construction systems such as Unigraphics in the 3D area and Euclid in 3D programming, we implement even the most complex requirements.Our powerful CNC technology, including in the process wire and sinker EDM, milling, HSC milling, grinding as well as the experience of mold makers since 1991 ensure rapid and complete production runs. The mass production and prototype molds are patterned in our injection molding machines and, if necessary, we assume the pre-series and series production of plastic parts. Industries (applicable for the entire group SMK) Engineering / Special Engineering / Valve Industry / Drive and gear engineering / automotive industry / Apparatus / equipment / Automation Technology / Control Engineering / Agriculture and forestry machinery / piping engineering / environmental / medical / Energy Management / railway technology / food technology Quality (applicable for the entire group SMK) Certified quality by qualified employees and structured pr...

Please allow me to introduce our company. We are a Slovak company whose major production program is orientated to manufacturing of special and precise parts for machines, different kind of fixtures, stamping tools, dies/progressive tools and transfer tools. We are a member of Rejlek Plastics Group in Vienna, Austria. We offer you capacities and experience in design and production. Our production is for the customers who are different tools and machine producers, special machine builders working in the automotive industry, electrotechnical and furniture industry and in automatization of industrial manufacturing. If you are interested in cooperation with our company, do not hesitate to call us. Yours sincerelly Viena International Slovakia

We are a metal-working craft business with the advantages of a medium-sized company for 40 years, the second generation in the market. Flexibility, accuracy, timeliness are just a part of our strengths. Our customer base includes steel and engineering firms, manufacturers of special machines, piston manufacturers and retail customers. We process sheets from 0.5 to 160 mm thickness, profiles and pipes with a Konstruktionsgewischt from 100 gr to 5 tons of - Steel - stainless steel - aluminum - copper - Our qualified, experienced staff meet your tasks carefully and with high precision. Our products range from pure weldments on sheet metal parts, sheet metal panels complete, tubular structures, to install machined and finished part. In solving your technical problems, we are a competent partner for you.